数控线材折弯机 新型数控线材成型中心 数控弹簧机 二次加工机 自动送线架

地址:东莞市常平镇司马乡工业开发区松岭
電話:(0769)83829622
傳真:(0769)83970016

您现在的位置:首页 > 新闻资讯 > 公司新闻

你想知道线材成型机常见的故障都有哪些不?

作者:管理员 发布于:2019-09-09
无论在生产或使用过程中,设备故障都是正常现象,只要能及时处理,因为使用时间长,零件之间的磨损越来越多,那么故障就会出现,事实上,及时解决问题是好的,那么我们来看看这线材折弯机常见的故障。
环顾工作现场,清除妨碍工作和交通的杂物。地面上不得有油污,以免滑倒。工件应堆放整齐、牢固,防止坍塌和伤害。
检查线材成型机上的保护装置是否完好无损。如果未安装,则不允许驾驶。中频弯管机应具有良好的接地和电绝缘,电压应稳定。
检查线材成型机的光滑部位,缺油无油时,加足油。
空试运行时,检查机械运行是否正常,电气开关是否松动,使用是否方便。一切正常后,再做一次作业。
数控线材成型机
两个人同时工作时应该密切合作和协调。应指定专门人员操作开关。操作过程中不要和他人交谈或大笑,以防误操作。
机床启动时,操作人员不得离开机床。
数控线材成型机运行时,任何人不得靠近弯管行程范围,并建立保护警示标志。撬管子时要站稳,以免撬杆打滑伤人。操作员只能站在外面。
想要了解更多的线材成型机的相关资讯的http://www.gdmaisi.com/news
推荐炭黑胶头螺帽两个产品!
英语特配
Whether in production or in use, equipment failure is a normal phenomenon, as long as it can be handled in time, because the use of long time, wear and tear between parts more and more, then the failure will occur, in fact, timely problem solving is good, then let's look at the common fault of wire bender.

Look around the work site and remove the debris that hinders work and traffic. There must be no oil on the ground so as not to slip. Workpieces should be stacked neatly and firmly to prevent collapse and damage.

Check whether the protective device on the wire forming machine is in good condition. Driving is not allowed if not installed. Medium frequency pipe bender should have good grounding and electrical insulation, and the voltage should be stable.

Check the smooth part of the wire forming machine. When oil is short or no oil, add enough oil.

During the empty test run, check whether the machine is running normally, whether the electrical switch is loose, and whether it is convenient to use. Do your homework again after everything is OK.

Two people should work in close cooperation and coordination at the same time. Specialized personnel should be designated to operate the switch. Don't talk or laugh with others during the operation in case of misoperation.

When the machine tool is started, the operator must not leave the machine tool.

When CNC wire forming machine is running, no one should be close to the elbow travel range and establish protection warning signs. Stand firm when prying pipes so as not to slip and hurt people. Operators can only stand outside.

For more information on wire forming machines, http://www.gdmaisi.com/news

Recommend carbon black, rubber head nuts two products!

相关资讯
版权所有 Copyright(C)2018 东莞麦斯数控设备有限公司